Inicio > Foros
- Foros
- Overclocking y Benchmarks
- Overclocking
- Gente Que Tenga Exp, O A8n32 Y Xms4400 Ddr550mhz
Resultados 1 al 9 de 9
Tema: Gente Que Tenga Exp, O A8n32 Y Xms4400 Ddr550mhz
-
03/07/2007, 06:23
Gente Que Tenga Exp, O A8n32 Y Xms4400 Ddr550mhz
Hola a todos. Antes que nada, gracias de antemano a los que me intentais leer/ayudar.
Mi problema es el siguiente:
Tengo desde hace ya un tiempo los siguientes componentes:
1-Opteron 170 - CCBWE-0550UPMW
2-A8N32 SLI Deluxe - BIOS 1303
3-Corsair Twinx-2048 4400 PRO - DDR550mhz
4-Fuente Zalman 600w
5-Disipador Big Typhoon+ Papst 12cm - 1600rpm
6-X1900XT Sapphire
Se que el stepping del micro no es muy alla (le saco los 2500 con 1.45), y francamente, no me importa ya hacerme a la idea de que no voy a exprimirlo mas (aunque si pudiera subirlo algo mas despues de que alguien en este post pudiera ayudarme, bienvenido seria dicha mejora, claro). El problema viene de el resto de configuraciones que he hecho para poder sacarle partido a las memorias, ya que ninguna es estable, salvo esta, que es la que actualmente uso:
multiplicador-10
voltaje-1.45
fsb-250
htt x4
latencias-2.5-3-3-7 a 2.8
Bien, pues conocimientos, tengo unos pocos, pero mas bien mi aprendizaje ha sido bajo presion, y se que la verdadera informacion esta toda en ingles, y no es muy bueno que digamos(o yo no conozco buenas webs, excepto esta, claro), asi que ya no se que hacer, a quien recurrir, etc. Como he dicho antes, lo del micro lo tengo bastante asumido, pero me da rabia no poder poner las memos a la velocidad nativa, que no es que quiera subirle mas, es solo ponerla a la nativa.
Uno de los fallos que me da cuando intento probar otras configs es que mientras que el Orthos me es relativamente estable (no lo he probado mucho, unas pocas horas), pero cuando voy a poner el 3dmark05, se queda colgado, dandome un mensaje de error de la grafica (esto solo ocurre cuando uso el multiplicador a 9 o mas bajos). He probado a subirle el pci-e frecuency de la placa, pero no consigo nada, y no hay mas opciones para la grafica referidas en la bios.
Total, que he probado a bajar multiplicador, subir fsb, leer guias varias, dar voltaje extra, de todo, vamos.
Agradeceria cualquier tipo de ayuda, preferiblemente con un equipo similar, para poder ir al grano y no molestar/perderme demasiado, y en definitiva, probar varias configuraciones hasta dar con una que sea lo mas robusta posible, y me permita usar las memos a lo que dan por defecto:550mhz, que para lo caras que me salieron...
Mi correo es:ruyghost2501@hotmail.com. Estare pendiente a este foro, pero por si hicieran falta otros metodos de comunicacion, podeis agregarme incluso al messenger, todo con tal de quitarme este muerto de encima.
Nada mas, lo dicho. Si necesitais alguna info mas complementaria, poneros en contacto conmigo, o simplemente responded en el hilo.
Muchas, muchas gracias a todos.
Saludos.
-
05/07/2007, 14:03jotiocomomola
- Fecha de ingreso
- 06 jul, 06
- Mensajes
- 770
A ver si te puedo ayudar, empezando por la configuración de la BIOS de la placa, en ingles pero facilón:
A8N32 Quickie OC guide
Luego el micro, de un post que abrí en su día en otro foro USA:
Models:
* 165 (1.8 GHz)
* 170 (2.0 GHz)
* 175 (2.2 GHz)
* 180 (2.4 GHz)
[edit]
Stepping Info
* CCBWE are less likely to be coldbugged.
* CCBBE and CCB1E are very likely to be coldbugged.
* Averaging >=2800
* CCB1E 0550VPMW
* CCB1E 0605XPMW
* CCB1E 0608MPMW
* CCB1E 0609FPMW/FPAW
* CCBBE 0610DPMW (most consistent for 3GHz +)
* CCBBE 0615DPMW/EPMW
* CCBBE 0617FPMW
* CCBWE 0602BPMW
* Averaging 2600-2800
* CCB1E 0606FPMW
* CCB1E 0609FPBW
* CCBWE 0530TPMW
* CCBWE 0546XPMW/MPMW
* CCBWE 0550UPMW/VPMW :!: :!: :!:
* Averaging <=2600
* CCBWE 0534SPMW
* CCBWE 0541RPMW
* CCBWE 0543TPMW
* CCBWE 0551UMPW/VPMW
* CCBWE 0604TPMW
* CCBWE 0607UPBW
* CCBWE 0609FPAW
De aquí se desprende que tu micro debería ser capaz de algo más.
Luego las memorias, seguramente tienes un problema con los timings que la placa no maneja bien en AUTO (by SPD). Si en la web del fabricante no te salen TODOS los timings, tendrás que hacer prueba y error. La placa tiene dos apartados para esto, uno con los timings básicos que los pondrás manualmente y otro con "aditional timings" creo recordar, que dejaras gestionar por la placa.
Cuando llegue a casa posteo la explicación de los timings para que veas como y cuales modificar.
-
05/07/2007, 16:31jotiocomomola
- Fecha de ingreso
- 06 jul, 06
- Mensajes
- 770
Lo prometido es deuda:
Memory Timings
The Big 5
Most motherboard had manual adjustments for “The Big 5” memory timings. These are
CAS Latency (tCL)
RAS-to-CAS Delay (tRCD)
RAS Precharge (Trp) (AKA: Row Precharge)
Act-to-Precharge Delay (tRAS) (AKA: Min Ras# Active Time)
Command-Per-Clock (CPC) (AKA: Command Rate)
The first 4 are typically publicly specified by Ram manufactures in the order listed. For Example,:
OCZ Gold BH-5 is Specified at PC3200 with Timings of 2-2-2-8. tCL, tRCD, and tRP are all “2” and Tras is “8”
OCZ Value (VX) is specified at 2.5-3-3-7. tCL-2.5, Trcd-3, Trp-3, Tras-7 (But we all should know by now those are just a starting point)
CPC will be covered in depth in the next section.
What do the “big 5” settings do and what are their effects on Speed/Bandwidth?
tCL: CAS controls the amount of time between receiving a command and acting on that command.
Typical Settings: 2,2.5,3
Effects: Large Effect on Bandwidth and Stability
NOTE: BH5/BH6 typically will NOT run at anything higher than 2
tRCD: tRCD is the cycle time between the first stage in memory access, the row strobe, and the second stage.
Typical Settings: 2,3,4,5
Effects: Medium Effect on Bandwidth and Large effect on Stability
tRP: tRP is the amount of time it takes for memory to terminate the access in one row and begin another.
Typical Settings: 2,3,4,5
Effects: Medium Effect on Bandwidth, Large effect on Stability
tRAS: tRAS is the time between receiving a request for data electronically on the pins of a memory module and then initiating RAS to start the actual retrieval of data.
Typical Settings: 5,6,7,8,9,10
Effects: Minimal Effect on Bandwidth, Medium effect on Stability
CPC: This is the delay between when a IC is selected and the time commands can be issued to the IC. The more chips on a module (Single vs. double sided) the more difficult it is for the memory controller to do this in 1 command clock. Most quality modules with an A64 Processor can do 1T rates on 256 and 512mb modules. 2T can increase your overclock but at a substantial loss in bandwidth.
Typical Settings: 1T,2T
Effects: Large effect on Bandwidth, Medium effect on Overclocking
Extended memory settings
These settings are found on DFI Nforce3/4 boards and many of them can be found in bios’ from other manufacturers as well. Exact definitions are rather hard to find, but I’ve found lots of references to these timings as well as done extensive testing with A64 Tweaker to be able to report these findings.
Row Cycle Time (tRC)
Typical Settings: 7-14
Effects: Large Influence on Bandwidth/Stability.
Row Refresh cycle time (tRFC)
Typical Settings:11-17
This timing is usually always set to 2-4 clocks higher that the tRC.
Effects: Large Influence on Bandwidth/Stability.
Row to Row Delay(also called Ras to Ras delay)(tRRD)
Typical Setting:0-4
Effects: Slight Influence on Bandwidth/Stability.
Write Recovery Time (tWR)
Typical Settings: 2, 3
Effect: Minimal Influence on Bandwidth/Stability.
Write to read Delay (tWTR)=
Typical Setting: 1, 2.
Effect: Minimal Influence on Bandwidth/ Stability.
Read to Write delay (tRTW)
Typical Settings1-4
Effects: Minimal Influence on Bandwidth/Stability.
Write CAS# Latency (tWCL)
Typical Setting:AUTO/1
Note from RGone of DFI: Note from RGone of DFI-Street.com Posts with AUTO,1 or 5 in setting works on my board with “any” brand or size and speed of memory!
Effect: Large Influence on Stability.
DQS skew Control
Settings: Auto, Increase Skew, Decrease Skew.
Effects: Increase for performance, and Decrease for Stability,
Minimal Influence on Bandwidth/Stability.
DQS Skew Value*= 0-255 in 1.0 increments. This is the value that is Increased or Decrease when you set the DQS skew control. I typically run 125 Increase on my BH-5
DRAM Drive Strength
Typical Settings: Level 1-4
Effects: Level 1 should be run with CPC Enables, I had instability with anything else Some People others have had success w/ using level 2-4 if CPC is disabled(2T).
Large Influence on Stability.
Max Async. Latency
Typical Setting: 5.0-10.0 (7.0 netted the best results on my BH-5)
Effects: Minimal Influence on Bandwidth/Stability.
***8-9 may help increase stability when using HTT speeds of 300+
Read Preamble time
Typical Setting: 4.0-7.0 (5.5 netted the best results on my BH-5)
Effects: Minimal Influence on Bandwidth/Stability.
***5.5-7 may help increase stability when using HTT speeds of 300+
Idle Cycle Limit 000-256 in doubled increments.
Minimal Influence on Bandwidth/Stability.
Dynamic Counter
Typical Setting: Auto, Enable, Disable. Enable for Slight Performance increase, Disable for slight Stability increase
Minimal Influence on Bandwidth/Stability.
Refresh Period (tREF)
Typical Setting: AUTO/0032-4708 in variable increments.
Typical translations: Some motherboards have more options than listed here, but I have not found what they us values are for the addition settings so they are not included.
---------------------
0388= 100mhz(15.6us)
0516= 133mhz(15.6us)
0648= 166mhz(15.6us)
0780= 200mhz(15.6us)
---------------------
0908= 100mhz(7.8us)
1032= 133mhz(7.8us)
1168= 166mhz(7.8us)
0016= 200mhz(7.8us)
---------------------
1536= 100mhz(3.9us)
2048= 133mhz(3.9us)
2560= 166mhz(3.9us)
3072= 200mhz(3.9us)
---------------------
3684= 100mhz(1.95us)
4196= 133mhz(1.95us)
4708= 166mhz(1.95us)
0128= 200mhz(1.95us)
I’ve found 3.9us to be the best setting for my BH-5, 15.6 results in slightly lower bandwidth, but the same stability it seems.
Effects: Minimal effect of Bandwidth, Minimal to Extreme effect of stability
**Make SURE your tREF setting is set to a value related to your memory Divider! Extreme system instability will result if this is not matched up!
When using the DFI Specific dividers I’ve left this on “AUTO” , Once I finish deciphering the settings, I will add to the list.
R/W Queue Bypass
Typical Setting: 8x, 16x.
Minimal Influence on Bandwidth/Stability (Lower slightly increases stability).
Bypass Max
Typical Setting: 4x-7x
5x-7x for max performance,0x-4x has shown to increase overclock slightly
Minimal Influence on Bandwidth/Stability.
32 byte Granulation
Typical Setting: Disable (8burst), enable (4burst).
Effect: Try Disable (8burst) for more bandwidth. Try enabling 4 burst for more stability
Minimal Influence on Bandwidth.
-
05/07/2007, 16:51jotiocomomola
- Fecha de ingreso
- 06 jul, 06
- Mensajes
- 770
Vamos con nuestra BIOS:
ADVANCED - CPU config
Ponemos 1T para empezar, pero podemos bajar a 2T si la cosa falla.
ADVANCED - CPU config - Memory setting - Memory Config
Memclock mode > LIMIT
Memclock mode > son los divisores 100-133-166-200
MCT Timing MODE > MANUAL (entramos a trapo)
+++++++++ Típicos (Tú 2.5-7-3-3) (Prueba 3-8-4-4)
CAS - Typical Settings: 2,2.5,3
TRAS - Typical Settings: 5,6,7,8,9,10
TRP - Typical Settings: 2,3,4,5
TRCD - Typical Settings: 2,3,4,5
+++++++++ Si no tienes info en la web, ensayo y error (el CPUz te puede dar alguna pista), aunque la mayoría tienen Effects: Minimal Influence on Bandwidth/Stability.
TRRD - Typical Setting: 0-4
TRC - Typical Settings: 7-14
TRFC - Typical Settings: 11-17
TRWT - Typical Settings: 1-4
MCT Extra> AUTO
-
10/07/2007, 06:30
Gracias...
Gracias mil, tio, te debo una. En cuanto pueda me meto al tajo y pruebo algunas cosas, y te informare del resultado. Gracias por la ayuda y la info, espero que me sirva.
Te informo, un saludo!
-
21/07/2007, 17:24Ruyman78
- Fecha de ingreso
- 20 jul, 07
- Mensajes
- 2
Ehhh, hola???
Ey tio, soy el del pc que no podia overclokear, el de los posts de mas arriba. Por si no has leido el PM que te envie, te mando esto, a ver si esto te llega, ok¿?a ver si me puedes echar una mano, porque no hay manera de poder poner aquello a funcionar, y ya estoy cogiendo complejo, je.
Gracias, un saludo
-
22/07/2007, 21:22Ruyman78
- Fecha de ingreso
- 20 jul, 07
- Mensajes
- 2
hooola, alguien me lee?
-
06/10/2007, 22:00
hola
-
17/10/2007, 07:30
LK;
不能说的秘密 我们说好的 勇敢的心 有没有人告诉你 还不是因为爱 思念 落叶归根 杀手 初次与你相遇 我对天空说 爱死了昨天五月天 免费点歌 五月天 铃声 铃声下载 铃声下载 铃声下载 手机铃声下载 手机铃声下载 手机铃声 手机铃声 手机铃声 mp3铃声 mp3铃声 mp3铃声下载 mp3铃声下载 mp3铃声下载 搞笑铃声 搞笑铃声下载 手机图片 手机图片 手机游戏下载甲 免费点歌 免费点歌 免费点歌 手机点歌 手机点歌 手机铃声免费下载 黄金甲 爱我就别伤害我 菊花台 菊花台 离歌 皇后与梦想 谁动了我的琴弦 如果爱下去 老公老公我爱你 夜的第七章 那一夜 我们都是好孩子 月亮之上 一万个理由 我的果汁分你一半 将军令 皇后与梦想 听妈妈的话 今天你要嫁给我 一万个理由 放开 暖暖 爱情转移 千年泪 爱的天灵灵 发现爱 我会好好的 中国话 该死的温柔 我怀念的
千里之外 不怕不怕 隐形的翅膀 求佛 死了都要爱 QQ爱 号码 曹操 大城小爱 寂寞沙洲冷 狼爱上羊 认真的雪 香水有毒不怕不怕 秋天不回来 千里之外 太美丽 冰吻 不要再来伤害我 让泪化作相思雨 让泪化作相思雨 我不后悔 香水有毒 亲亲 秋天不回来 求佛 大城小爱 QQ爱 不怕不怕 月亮之上 曹操 一万个理由 神话 那一夜 狼爱上羊 老婆老婆我爱你 大喜宙 你到底爱谁 我的果汁分你一半 将军令 一万个理由 美丽的神话 我的果汁分你一半 香水有毒 香水有毒 大喜宙 我的果汁分你一半 千里之外 秋天不回来 号码 死了都要爱 不怕不怕 求佛 皇后与梦想 离歌 认真的雪 隐形的翅膀 今天你要嫁给我 听妈妈的话 将军令 菊花台 大城小爱 曹操 菊花台 认真的雪 隐形的翅膀 月亮之上 千里之外 秋天不回来 求佛 菊花台 离歌 今天你要嫁给我 认真的雪 隐形的翅膀 月亮之上 千里之外 秋天不回来 求佛 生日礼物 江南 我不后悔 披着羊皮的狼 不要再来伤害我 不得不爱 睫毛弯弯 生日礼物 嘻唰唰 Perhaps Love 老公老公我爱你 笔记 yeyeye 童话 直来直往 你是我的玫瑰花 一千年以后 Ring Ring Ring 花田错 大舌头 桃花朵朵开 寂寞沙洲冷 我赚钱了 因为我是女人 在梅边 月桂女神 披着羊皮的狼 walking in the sun 香水有毒dj 就是爱你 嘻唰唰 不要再来伤害我 god is a girl 彩虹天堂 无尽的爱 夜曲 下辈子不要做男人 毛主席语录 生日领悟 快乐崇拜 发如雪 美丽的神话 O ZONE 那一夜 反转地球 爱情攻略 吻别 为什么相爱的人不能在一起 恶作剧 老婆老婆我爱你 女人花紫藤花 功夫 面具 醉清风 两只蝴蝶 人鱼的眼泪 小薇 黑色毛衣 右手戒指 女友与好友 你一定要幸福 千年泪 触电 新上海滩 唇唇欲动 算你狠 笑傲江湖 冰吻 宫 我们怎么了 铁血丹心 莫斯科没有眼泪 小熊 绿洲 我不想说我是鸡 遇见 七天七世纪 回来我的爱 大海 被爱伤过的人 完美世界 不值得 情圣 宝宝唱歌 你那么爱她 水手 I saw you walking in the rain 皇帝 手机 恋着多喜欢 三只熊 幸福毛毛虫 解脱 没有钱你会爱我吗 再回首 心肝宝贝 阳光版串烧 着迷 爱你不会变 笔记 广岛之恋 你到底爱谁 我的SHOW i think i 一直很安静 哎呀 漫步人生路 大话西游 我爱你 爱情木瓜 独一无二 爱上贝克汉姆 take me to you heart 假装 一万个理由 爱海滔滔 我们的纪念日 你的选择 冬天快乐 原来 爸爸妈妈 猪八戒背媳妇 女人心 光芒 大悲咒 美丽的神话 天下无双 一千年以后 手放开 赤道和北极 暧昧 没有钱你会爱我吗 莫斯科没有眼泪 怒放的生命 梁祝 七月七日晴 江南 秋日恋歌 珊瑚海 我要的世界 你那么爱她 飞舞 雨樱花 童话 甜蜜的我爱你 想唱就唱 月亮之上 天路 I think I 想起 Mr.Q 阿根廷别为我哭泣 暧昧 发如雪 亲嘴 一路向北 TAKE ME TO YOUR HEART 唱的响亮 蜡笔小新 我是你老公 宁夏 天鹅 断点 loving you 真爱 丁香花 我的心里只有你没有他诗人的眼泪 完美的互动 雪之花 不痛 迷魂计 only you 彩云追月 我们能不能不分手 我不后悔 我的名字叫伊莲娜 超合金曲 爱我别走 三国恋 无赖 电话预报 孤单北半球 吉祥三宝 黑色毛衣 Balla Da Li 为什么相爱的人不能够在一起 幼稚园 来电 小狗序曲 狼爱上羊 一千零一夜 我要我的滋味 god is a girl 浪漫手机 酸酸甜甜就是我 老狼请吃鸡 遇上爱 我恨我痴心 红颜 明明很爱你 你现在 我很想爱他 谢谢你的爱 孤单爱情海 as long as you love me 化蝶 让泪化作相思雨逍遥叹ariari夜半狼嚎寂寞在唱歌摇头舞霸突然的自我 melody 大话西游 我们的爱 遗失的美好 上海滩 OleOle我们是冠军 月半弯 水晶蜻蜓 真爱 你有短消息 化蝶 愿望 平底鞋女 平行线 雨人 爱你不是两三天 东南西北风 沧海一声笑 承诺 鬼来电 遗失的美好 过云雨 家在东北 风筝 勇气 偏偏喜欢你 讲不出再见 竹林风 喜欢你没道理 Lydia 白月光 my love 六月的雨 北极星的眼泪 下辈子如果我还记得你 如果的事 挥着翅膀的女孩 无赖 只对你说 那一夜 我不够爱你 做人要厚道 我要抱着你 亲爱的不要离开我 恶作剧 枫 甜蜜蜜 谁说喝醉就无所谓 北国之春 蓝莲花 古灵精怪 O ZONE 赤道与北极 浪漫满屋 错误的相遇 眉飞色舞 好心分手 戏中有气 一个像夏天一个像秋天 痛彻心扉 光辉岁月pretty boy虞美人 猪之歌 心醉 欧若拉 千千阙歌 你爱我像谁 冲动的惩罚 追梦 爱的就是你 再度重相逢 冰菊舞 爱的代价 忘不了 海阔天空 分飞 后来 决战斗室 漫步人生路 恭喜发财 东风破 婚前的女人 天涯 见习爱神 分开旅行 小强 我爱周星星 如果真爱我 面具 如果真爱我 面具 一口一口 放生 天下大同 第一次 就是爱你 kiss goodbye 第一滴泪 发财了 我的未来不是梦 太早 月半弯 赤道和北极 想念你的歌 2002年的第一场雪 Daddy-DJ 万里长城永不倒 分飞 把悲伤留给自己 my heart will go on 给我你的爱 想唱就唱 飞的更高 倩女幽魂 心型圈 恋爱达人 最初的梦想 Give Me Five 爱我还是他 普通朋友 花好月圆夜 黑白世界 外婆桥 再唱回心转意 七年的爱小叮当之歌我们的爱壁虎漫步 琥珀 qq爱 昨日重现 We Well Rock You 老地方 想起 十分钟 敢不敢流行主教 天灰 分手后的夜 笔记 拥抱我失恋的人不能听 天籁之音 老鼠爱大米 化蝶飞 青藏高原 情非得已 黄健翔激情解说 谢谢 爱很简单 the way u are QQSMS 其实我很在乎你 命运 一帘幽梦 天空 飞行部落 [url=http://www.zhangxiu.com/send/s
Powered by vBulletin® Version 4.2.5
Copyright © 2025 vBulletin Solutions, Inc. All rights reserved.
Traducción por vBulletin Castellano Copyright © 2025.
Copyright © 2025 vBulletin Solutions, Inc. All rights reserved.
Traducción por vBulletin Castellano Copyright © 2025.
AutoLinker v1.3 by Poker Forum