Bios Estable GA-X58A-UD7 i7 920@4000

[Daemonaz]

Buenas, después de unos días intensos, puedo dedicarle un rato al pc.

Pongo bios que tengo ahora, a ver si encuentras alguna incoherencia.

X58A-UD7:
MB Intelligent Tweaker(M.I.T.)
Advanced CPU Features {Press Enter]
CPU Clock Ratio............................ [19 X]
CPU Frequency .....(Ghz)................... 3,8GHz (200x19)
Intel(R) Turbo Boost Tech.................. [Disabled]
CPU Cores Enabled.......................... [All]
CPU Multi-Threading........................ [Enabled]
CPU Enhanced Halt (C1E).................... [Enabled]
C3/C6/C7 State Support..................... [Enabled]
CPU Thermal Monitor........................ [Disabled]
CPU EIST Function.......................... [Disabled]
Bi-Directional PROCHOT..................... [Enabled]
Virtualization Technology.................. [Enabled]

Uncore & QPI Features [Press Enter]
QPI Clock Ratio ............................ [x36]
QPI Link Speed (Ghz)........................ 7.2GHz
Uncore Clock Ratio ......................... [x16]
Uncore Frequency (Mhz)...................... 3200MHz
Isochronous Support ........................ [Enabled]

Advanced Clock Control [Press Enter]
>>>>>Standard Clock Control
Base Clock (BCLK) Control ................. [Enabled]
BCLK Frequency (Mhz) ...................... [200]
PCI Exxpress Frequency (Mhz)............... [100]
>>>>>Standard Clock Control
CPU Clock Drive ........................... [700mV]
PCI Express Clock Drive .................. [700mV]
CPU Clock Skew ............................ [ 0ps]
IOH Clock Skew ............................ [ 0ps]

Advanced Dram Features [Press Enter]
Performance Enhance........................ [Extreme]
Extreme Memory Profile (X.M.P.)............ [Disabled]
System Memory Multiplier (SPD)............. [8.0]
Memory Frequency (Mhz)..................... 1600
DRAM Timing Selectable (sPD) .............. [Quick]
Profile DDR Voltage ....................... 1.5V
Profile QPI Voltage ....................... 1.175V
>>>>> Channel A
CAS Latency Time ..............8...... [6]
tRCD ..........................8...... [8]
tRP ...........................8...... [6]
tRAS ..........................8...... [24]
Command Rate (CMD) ............1...... [1]
>>>>> Channel B
CAS Latency Time ..............8...... [6]
tRCD ..........................8...... [8]
tRP ...........................8...... [6]
tRAS ..........................8...... [24]
Command Rate (CMD) ............1...... [1]
>>>>> Channel C
CAS Latency Time ..............8...... [6]
tRCD ..........................8...... [8]
tRP ...........................8...... [6]
tRAS ..........................8...... [24]
Command Rate (CMD) ............1...... [1]

Advanced Voltage Control [Press Enter]
Voltage Types Normal Current
>>>>CPU Voltages
LoadLine Calibration .......................... [Level 2]
CPU Vcore ..................... 1.225V ........ [1.35V]
Dynamic Vcore (DVID) ......... +0.00000V ...... Auto
QPI/VTT Voltage ................ 1.175V ....... [1.335V]
CPU PLL ........................ 1.800V ....... [1.800V]
>>>>>MCH/ICH Voltrage
PCIE............................ 1.500V ....... [1.500V]
QPI PLL......................... 1.100V ....... [1.100V]
IOH Core........................ 1.100V ....... [1.100V]
ICH I/O......................... 1.500V ....... [1.500V]
ICH Core........................ 1.100V ....... [1.100V]
>>>>>Dram
DRAM Voltage ..................... 1.500V ...... [1.640V]
DRAM Termination ................. 0.750V ...... Auto
Ch-A Data Vref ................... 0.750V ...... Auto
Ch-B Data Vref ................... 0.750V ...... Auto
Ch-C Data VRef ................... 0.750V ...... Auto
Ch-A Address Vref ................ 0.750V ...... Auto
Ch-B Address Vref ................ 0.750V ...... Auto
Ch-C Address VRef ................ 0.750V ...... Auto

[Daemonaz]

Mira se los posteé a un gañán que ni ha respondido.....es un foro guiri

http://www.clunk.org.uk/forums/overcloc ... mps-4.html

A lo mejor por tu Xfire necesitas más Qpi pero de momento prueba así

ya me dirás.....

Ya lo probé con esta configuración y las gráficas hicieron unos fallos (la pantalla se puso un segundo con ruido gris, como en las antiguas teles cuando buscabas un canal). Pensé que algo estaba mal, y volví a 3.8.

[Daemonaz]

Advanced CPU Features:
CPU Clock Ratio [20x]
Intel(R) Turbo Boost Tech [Disabled]
CPU Cores Enabled [All]
CPU Multi Threading [Enabled]
CPU Enhanced Halt (C1E) [Disabled]
C3/C6/C7 State Support [Disabled]
CPU Thermal Monitor [Disabled]
CPU EIST Function [Disabled]
Virtualization Technology [Enabled]
Bi-Directional PROCHOT [Enabled]

Uncore & QPI Features:
QPI Link Speed [x36]
Uncore Frequency [x16]
Isonchronous Frequency [Enabled]

Advanced Clock Control:
Base Clock (BCLK) Control [Enabled]
BCLK Frequency (MHz) [210]
PCI Express Frequency (MHz) [103]
C.I.A.2 [Disabled]

[B]Advanced clock control:[/B
]CPU Clock Drive [ 700mV]
PCI Express Clock Drive [ 700mV]
CPU Clock Skew [ 0ps]
IOH Clock Skew [ 0ps]

or

[B]Advanced clock control:[/B
]CPU Clock Drive [ 700mV]
PCI Express Clock Drive [ 900mV]
CPU Clock Skew [ 0ps]
IOH Clock Skew [ 0ps]

or

[B]Advanced clock control:[/B
]CPU Clock Drive [ 800mV]
PCI Express Clock Drive [ 800mV]
CPU Clock Skew [100ps]
IOH Clock Skew [ 100ps]



Performance Enhance [Disabled]
Extreme Memory Profile (X.M.P.) [Disabled]
System Memory Multiplier (SPD) [6.0]
DRAM Timing Selectable (sPD) [Configure the timmings to RAM specifications never use auto)
I would try 1st 10-10-10-30 and if it works would go to 9-9-9-27 and if so....8-8-...

Load Line Calibration [level 2]
CPU Vcore 1.29375v [1.31250]
QPI/VTT Voltage 1.150v [1.355v]
IOH Core 1.100v [1.120v]
DRAM Voltage 1.5v [1.60v]
CPU PLL 1.800v [1.400v]

MCH
PCIE 1.500v [1.540]
QPI PLL 1.100v [1.140v]
IOH Core 1.100v [1.120v]
ICH I/O 1.500v [1.580]
ICH Core 1.1v [1.140]

Esto es lo que tenias posteado, y me pasó el linx, pero hizo el error que te he comentado. Puede ser por darle al pci en vez de 100, 103 Mhz?

[PLAY911]

Vamos poco a poco----si te parece vamos a ponerlo primero a 4.0 con HT on y luego vamos a por los 4.2----la UD7 es muy puñetera y la configuración entre 4.0 y 4.2 es muy diferente
Prueba esto

Advanced CPU Features:
CPU Clock Ratio [20x]
Intel(R) Turbo Boost Tech [Disabled]
CPU Cores Enabled [All]
CPU Multi Threading [Enabled]
CPU Enhanced Halt (C1E) [Disabled]
C3/C6/C7 State Support [Disabled]
CPU Thermal Monitor [Disabled]
CPU EIST Function [Disabled]
Virtualization Technology [Enabled]
Bi-Directional PROCHOT [Enabled]

Uncore & QPI Features:
QPI Link Speed [x36]
Uncore Frequency [x16]
Isonchronous Frequency [Enabled]

Advanced Clock Control:
Base Clock (BCLK) Control [Enabled]
BCLK Frequency (MHz) [200]
PCI Express Frequency (MHz) [101]
C.I.A.2 [Disabled]

[B]Advanced clock control:[/B
]CPU Clock Drive [ 700mV]
PCI Express Clock Drive [ 700mV]
CPU Clock Skew [ 0ps]
IOH Clock Skew [ 0ps]


Performance Enhance [Disabled]
Extreme Memory Profile (X.M.P.) [Disabled]
System Memory Multiplier (SPD) [6.0]
DRAM Timing Selectable (sPD) [Configure the timmings to RAM specifications never use auto)
I would try 1st 10-10-10-30 and if it works would go to 9-9-9-27 and if so....8-8-...

Load Line Calibration [level 2]
CPU Vcore 1.29375v [1.31250]
QPI/VTT Voltage 1.150v [1.355v]
IOH Core 1.100v [1.120v]
DRAM Voltage 1.5v [1.60v]
CPU PLL 1.800v [1.400v]

MCH
PCIE 1.500v [1.540]
QPI PLL 1.100v [1.140v]
IOH Core 1.100v [1.120v]
ICH I/O 1.500v [1.580]
ICH Core 1.1v [1.140]

[Daemonaz]

Ok. Linx pasado, todo,ok. Acabado sin errores, 20 pasadas. Voy a probar el battlefield.

A ver si hay suerte

[Daemonaz]

Performance Enhance [Disabled] esta opcion me sale o standar, turbo o extreme
C.I.A.2 [Disabled] esta opcion no me sale en bios

[Daemonaz]

Y tambien me salen
Channel interleaving 6 [auto]
Rank interleaving 4 [auto]

[PLAY911]

deja en auto Channel Interleaving y Rank y el perfomance ponlo en Standard o Turbo.

"carbura" ok con el BF?

[Daemonaz]

Ahora el bt tiene una actualización, y esta no encuentra el temp. Estoy probando instalarlo otra vez, ya que cambiando los temps otra vez a c:, tampoco va...

[Daemonaz]

Ahora no puedo ni instalar el origin.
Error! Can,t initialize plug-ins directory.

Que rollazo......