[AF] Andreoid & Finnzwerg retoques watercool (muchas fot

Unfortunately I can not make such amazing photos
for now I'll show some new models ^^
a new fullcover light waterblock for the MSI 890GXM-G65

the cool links, like the 790 or 890FX cooler, the NB with the voltage transformers
I have decided against engraving, because the arm is very thin
http://anfi-tec.de/forenbilder/marc/MSI_890GXM-G65.jpg

http://anfi-tec.de/forenbilder/marc/...GXM-G65(1).jpg

the Sapphire IPC AM3DD785G NB & SB block i have made new too :)
(our Soleil01 cpu block as AMD Version)
http://anfi-tec.de/forenbilder/marc/..._AM3DD785G.jpg
close to the air cooler
http://anfi-tec.de/forenbilder/marc/2.jpg


when a slot milling soleil01 bottom,..some things can go wrong ...
here is the saw blade bursted
you can still see the remains of copper sheet in the bottom
as a time to say, there is no action at a water cooling :D
http://anfi-tec.de/forenbilder/marc/1.JPG


this weekend will get an Asus Crosshair IV Formula (AMD 890FX)
http://anfi-tec.de/forenbilder/marc/3.jpg
There will probably come a full light as the 790FX
and maybe a total fullcoverblock


.

Let's get for something of the tinkering which may be missing in no instance

the music ^^

I had 2 large PA speakers left, but the tweeter were broken
http://anfi-tec.de/forenbilder/09.11.26/1.JPG

opened and located
http://anfi-tec.de/forenbilder/09.11.26/2.JPG

the small hair-wires were torn down at the focal points -.-
http://anfi-tec.de/forenbilder/09.11.26/3.JPG

very thin
http://anfi-tec.de/forenbilder/09.11.26/4.JPG

So out of that glue
http://anfi-tec.de/forenbilder/09.11.26/5.JPG

soldered a new thicker wire
http://anfi-tec.de/forenbilder/09.11.26/6.JPG

Top out again, and solder them
http://anfi-tec.de/forenbilder/09.11.26/7.JPG

tested works :) - assembling
http://anfi-tec.de/forenbilder/09.11.26/8.JPG

and in the new workshop
http://anfi-tec.de/forenbilder/09.11.26/9.JPG

-------------------------------------------------------

In the workshop it went on.
all the drawers were finished and the workintables were completed
http://anfi-tec.de/forenbilder/09.11.26/10.JPG

stuff-boxes
http://anfi-tec.de/forenbilder/09.11.26/11.JPG

computer for controling for cncs
http://anfi-tec.de/forenbilder/09.11.26/13.JPG

------------------------------------------------------

last but not least something for the watercooling-junkys:
I once i have tested whether Soleil fullcopperblock can be produced economically:
I have 3 pieces of milled
View from below:
http://anfi-tec.de/forenbilder/09.11...ildeckel/1.jpg

done (cut / thread / etc) from the bottom with Oring
http://anfi-tec.de/forenbilder/09.11...ildeckel/2.jpg

upside
http://anfi-tec.de/forenbilder/09.11...ildeckel/3.jpg

complete with bracket screws floor and then he looked like this:
http://anfi-tec.de/forenbilder/09.11...ildeckel/4.jpg

http://anfi-tec.de/forenbilder/09.11...ildeckel/5.jpg

http://anfi-tec.de/forenbilder/09.11...ildeckel/6.jpg

http://anfi-tec.de/forenbilder/09.11...ildeckel/7.jpg

http://anfi-tec.de/forenbilder/09.11...ildeckel/8.jpg

We will keep the top here and investigate whether any material change has an effect on the performance of the cooler

in large quantities (economic production) as the Soleil POM-top can not produce the fullcopperblock with our current resources
for everyone who does not know it yet:

Soleil01 with black pom-top
http://anfi-tec.de/forenbilder/09.11...ildeckel/9.jpg

the problems in producing the fullcopperblock are:
the bevel on mice top
The countersunk screws
The threading ger G1 / 4 "thread (I do this by hand, because the cordless electric screwdriver is to weak)
greater tolerance transgressions because the production is simply too difficult to edit material as plastic
maybe we could produce fullcopperblock economically with the big cnc later, but then it would kill the time by changing the cutting-tools manually

so an automatic tool change spindle for the big cnc must be purchased...
(but free in the required size, it will cost about € 10,000 incl
accessories such as tool holders, ac drives, pneumatic actuation)
*hmmpf* ... so saving money saving money saving money :'(
regards [ΛF] Andreoid

Hi Andrea.

Some time ago I follow your work both waterblocks as CNC (I'd seen in CNC Zone).

The truth is that I can only give you my congratulations.

Give me so jealous! The availability of a space dedicated to workshop!

I have my router installed in a room in a flat.

I send you a mp to make some inquiries.

A greeting.

Cita:

---

Iniciado por pritt

Hi Andrea.

---

please without the second "a" Andrea is a girls name ^^
my name is André ^^

Cita:

---

Iniciado por pritt

Some time ago I follow your work both waterblocks as CNC (I'd seen in CNC Zone).

---

you have seen my cnc on cnczone.com? o0 or did i misunderstood your sentence?

Cita:

---

Iniciado por pritt

The truth is that I can only give you my congratulations.

---

thx :)

Cita:

---

Iniciado por pritt

I have my router installed in a room in a flat.

---

no problems with the neighbours cause the loudness? :D

Cita:

---

Iniciado por pritt

I send you a mp to make some inquiries.

---

ok

Sorry about the name ... the translator.

The CNC Zone, do not you post the assembly of the workshop? ... it might be in another forum. It was seen that the assembly of the workshop and how to download the new CNC with a crane.

My router, then to avoid noise I have it in a "drawer."

A greeting.

so, after three weeks of waiting for the board by a user ...
the board simply does not come, and the user do not report to my mails
so I bought my own board. -.-

first putting the uninteresting cooler down :D
http://anfi-tec.de/forenbilder/10.06...sshair_4_9.jpg

for the voltage converter and north bridge, there is again a anfi-tec light cover
this is the cooler in the cad file, graphically
http://anfi-tec.de/forenbilder/10.06...sshair_4_7.jpg

simulated:
http://anfi-tec.de/forenbilder/10.06...sshair_4_8.jpg

and in real life :D
top only layed on
http://anfi-tec.de/forenbilder/10.06...sshair_4_1.jpg

distance of 22.5 mm g1/4" thread .. it also fits thick 16/10 :)
http://anfi-tec.de/forenbilder/10.06...sshair_4_3.jpg

the copper bridge already provided in the ocerclocked MSI790FX good temperatures ... then it will work at the asus too :)

Details:
http://anfi-tec.de/forenbilder/10.06...sshair_4_6.jpg

http://anfi-tec.de/forenbilder/10.06...sshair_4_5.jpg

http://anfi-tec.de/forenbilder/10.06...sshair_4_4.jpg

with the UCD (universal cooling device) SB in addition you get the board as completely cooled
should I draw a complete full cover block? (~ 12 hours of cad working)
I would at least have to mill about 10 blocks, so that the effort worthwhile for long cadding, ..

Now, you are asked:

1) a favorable light Cover + SB UCD is enough.
2) An elaborate Full Cover must be already.


regards
André

Continuing with the entrance into the workshop ... it had happened a lot.
The insulation-box has already been set up and the control PCs with monitors have been installed.
Works in comparison to the old workshop really lost in the space
http://anfi-tec.de/forenbilder/09.12.07/1.JPG

But before the CNCs were able to move back in the box, they had to be serviced in first.
http://anfi-tec.de/forenbilder/09.12.07/3.JPG

The Model-aluminum CNCs dont tolerate the coolant for miling and the copper in any way.
The CNC base are totally corroded. Thus, a AluCNC is nothing for eternity if one manufactures waterblocks.
http://anfi-tec.de/forenbilder/09.12.07/2.JPG

Then the machines into the box, and production begins ^^
http://anfi-tec.de/forenbilder/09.12.07/4.JPG

Large workshops want to accommodate large machines :D
our new helper
http://anfi-tec.de/forenbilder/09.12.07/5.JPG

handy :)
http://anfi-tec.de/forenbilder/09.12.07/6.JPG


although we have windows in the new workshop, one should not be missed,
The poster out of the first workshop... this now become indeed the third workshop ^^
hope we can stay in there for a longer time as in the other workshops -.-
http://anfi-tec.de/forenbilder/09.12.07/7.JPG

regards Andreoid

What coolant are you using?

I use white drilling and I have no cooroded.

... but, with copper, leak.

When I finish I'll try one that I bought at RDG Tools.

A greeting.

Cita:

---

Iniciado por pritt

What coolant are you using?

I use white drilling and I have no cooroded.

... but, with copper, leak.

When I finish I'll try one that I bought at RDG Tools.

A greeting.

---

we use some cheap coolant from ebay..
but this coolnt sux... i think it is not the best for health too

So i didn't post anything a long time ago... studies getting harder and harder.. spending more and more time with learning and writing tests
but now my tests of the last semester are over and i got the time to make some new blocks! :)

We got Asus crosshair IV extreme... overkclocking by iPhone... so this is the future of mainboards :D
so then,...lets cool this thing!
i made a 3D cad of the board,.. because this got to be complex
(the litle copper rings is the start of the waterblocks)
http://anfi-tec.de/forenbilder/10.10...20%2818%29.JPG

these rings will be connected tangential.. an so the blocks grows
http://anfi-tec.de/forenbilder/10.10...%20%281%29.JPG

between the PCI-E slot and the 4 capacitors i have space of ~ 8mm
if i design a waterchanel in there, it would kill every flow in the block
http://anfi-tec.de/forenbilder/10.10...20%2819%29.JPG

two lightcoverblocks or two fullcoverblocks
made the copperplates:
http://anfi-tec.de/forenbilder/10.10...%20%282%29.JPG

again the same problem... the space over the pwms is not wide enough for a chanel with a good waterflow -.-
http://anfi-tec.de/forenbilder/10.10...%20%283%29.JPG

so i took the lightcoverblock which established itself in the MSI790FX, MSI890FX,
890GXM-G65, ASUS Crosshair IV Formula, Asus M4A 890FX and in the EVGA P55 FTW 200.
http://anfi-tec.de/forenbilder/10.10...%20%287%29.JPG

i like this little tools in the cad program... radius tool :D
http://anfi-tec.de/forenbilder/10.10...%20%284%29.JPG

the SB Lightcover between the second and third graficcard with triple SLI.
the waterflow ist direct over the SB Chip.
http://anfi-tec.de/forenbilder/10.10...%20%285%29.JPG

NB PWM block, the waterflow ist direct over the NB Chip.
http://anfi-tec.de/forenbilder/10.10...%20%286%29.JPG

a view from the side. you can see the placement of the fittings between the graficcards
http://anfi-tec.de/forenbilder/10.10...%20%288%29.JPG

isometric angle
http://anfi-tec.de/forenbilder/10.10...%20%289%29.JPG

this here is interessting
the block and the board are in a cut view .. so that you can see the waterchanel, and the notch of the seal
http://anfi-tec.de/forenbilder/10.10...20%2810%29.JPG

although playing in 3D i have to test the correctness with an plexidummy
http://anfi-tec.de/forenbilder/10.10...20%2811%29.JPG

milling it in plexi
http://anfi-tec.de/forenbilder/10.10...20%2812%29.JPG

fits!
http://anfi-tec.de/forenbilder/10.10...20%2813%29.JPG

better than the plexidummy...the real ones in copper!
http://anfi-tec.de/forenbilder/10.10...20%2814%29.JPG

http://anfi-tec.de/forenbilder/10.10...20%2815%29.JPG

http://anfi-tec.de/forenbilder/10.10...20%2817%29.JPG

Finn and I are the first ones with offering the cooling set for this Asus crosshair IV extrem..
let's see how quickly the bigger manufacturers will follow us :)

-------------------------------------------------------------

today a test of our "UPC slim" was published

Our universal PWM "UPC slim" had been tested by the german watercoolingsite "Effizienzgurus.de" against a MVR-100-block by Koolance.
The UPC had got an efficiency-award! :)

next to a pair of pretty pictures and detailed descriptions of the coolers
there is still a flow test of both coolers (but unfortunately complete in german)
http://anfi-tec.de/forenbilder/10.10...%20%281%29.JPG

link to the test:
http://www.effizienzgurus.de/review/was ... daten.html

http://anfi-tec.de/forenbilder/10.10...%20%282%29.JPG

hmm somehow i cant see my pictures in here :)